Home / Thread Gages / #4-40 UNC
Unified Coarse · 40 threads per inch

#4-40 UNC Thread Gages

GO / NO GO thread plug gages for #4-40 UNC-2B and -3B internal threads, and thread ring gages for -2A and -3A external threads. Standard gages ship from stock to 2 weeks through authorized gage manufacturers, with calibration certificates available through our accredited partner labs.

Nominal size
0.1120"
Pitch
0.02500"
Basic pitch dia
0.0958"
Best wire size
0.01443"
Delivery
Stock–2 wks

What we supply in #4-40 UNC

Thread plug gages

GO and NO GO (HI) members, double-end or single-end, for checking #4-40 UNC-2B and -3B tapped holes and nuts.

Thread ring gages

GO and NO GO (LO) rings for checking #4-40 UNC-2A and -3A screws, studs, and machined external threads.

Set plugs & specials

Truncated and full-form set plugs for ring setting, plus modified pitch diameters, plated-thread and built-to-print gages quoted to your drawing.

Gages are supplied to ASME B1.2 gagemaker tolerances. Tell us the class, gage type, and quantity, and whether you need a calibration certificate with delivery.

Pitch diameter limits the gages check

A GO thread plug sits at the minimum pitch diameter of the internal thread and a NO GO (HI) plug at the maximum. A GO thread ring sits at the maximum pitch diameter of the external thread and a NO GO (LO) ring at the minimum. These are the product limits for #4-40 UNC, in inches:

ClassThreadPitch dia minPitch dia maxMajor dia minMajor dia maxChecked by
2AExternal0.09250.09500.10610.1112Thread ring gages
3AExternal0.09390.09580.10690.1120Thread ring gages
2BInternal0.09580.0991——Thread plug gages
3BInternal0.09580.0982——Thread plug gages

Computed from the ASME B1.1 formulas, with tolerances based on a length of engagement equal to the basic major diameter, as ASME B1.1 specifies for the UNC and UNF series. Class 2A carries an allowance of 0.0008"; class 3A has none. These are reference values: ASME B1.1 is the controlling document, and in a few sizes its published tables differ from the formula result by 0.0001" in the last place. Verify against the current standard before using them for acceptance.

Three-wire measurement

Measuring a #4-40 UNC-2A thread over wires with the best wire size of 0.01443", the measurement over wires runs from 0.11415" at minimum pitch diameter to 0.11665" at maximum, without lead angle correction. Enter your own wire size and reading in the three-wire pitch diameter calculator.

Calibration for #4-40 UNC gages

Already have #4-40 UNC gages in your crib? We manage their calibration through ISO/IEC 17025-accredited partner laboratories, at published prices: $12.00 per thread plug member and $19.00 per thread ring (standard pitch diameters, up to 2"). Each certificate is issued by the accredited lab that performs the work, with as-found and as-left data. Typical turnaround is 3 to 5 business days.

Straight talk: Walden Gage is a gage distributor and calibration broker, not a calibration laboratory. We do not hold an ISO/IEC 17025 accreditation ourselves. What you get from us is one contact, one purchase order, and one invoice for gages and calibration together. See all 370+ published calibration prices.

About the UNC series

The coarse series is the general-purpose fastener thread: fast to assemble, tolerant of handling damage, and the default on most prints. #4-40 UNC has 40 threads per inch on a 0.1120" nominal diameter.

What is the difference between 2A/2B and 3A/3B gages?
Class 2 is the standard commercial fit and the most common callout. Class 3 has a tighter pitch diameter tolerance and, on external threads, no allowance, for applications that need a closer fit. The gages differ because each is made to the limits of its class, so order the class shown on your print.
Do I need both a GO and a NO GO gage?
Yes. The GO member confirms the thread will assemble at maximum material; the NO GO member confirms the pitch diameter has not gone past its limit. A part that passes GO but also enters NO GO is out of tolerance.
Can you supply gages for plated or modified threads?
Yes. Gages for plated parts, modified pitch diameters, and special classes are quoted to your drawing or specification. Our pre-plate pitch diameter calculator shows the before-plating limits.

Other thread sizes

Same-day quote response

Need #4-40 UNC gages?

Tell us the class, gage type, and quantity. Standard gages ship from stock to 2 weeks.